Replace Nissan Key Fob Batteries
If your Nissan key fob isn't responding properly to your commands, it's likely that the battery is dead. It's a relatively easy repair that most people are able to do themselves.
You can get an upgrade from a hardware store or your owner's manual for the specific model you own You'll need follow these instructions to change the battery.
The Battery is changed
The key fob of your Nissan model comes with a lithium battery built-in that eventually loses its charge. The key fob's battery can be replaced in a matter of minutes. The first step is to purchase an additional CR2032 3V battery. It's a tiny coin cell battery often found in key fobs and it can be found at most convenience stores. You will also need gloves (latex or non-latex) and small screwdrivers with flat heads to open the fob. Check the owner's manual for a detailed guideline and steps before you begin.
Once you have the brand new battery, you can remove the old one by turning the fob on its side and looking at the back side. There will be a small catch that you have to release by pulling it down. This will release the mechanical key from its initial position inside the fob.
Then, insert the new battery and make sure that it is in the correct orientation. Close the fob once the battery has been placed and click the two sides of the fob together. Test your key fob after you have completed this step by pressing the unlocking button. If everything is in working and in good working order, you're ready to enjoy the Nissan's features. It's recommended to reprogram the key fob following the change of the battery to make sure it's functioning properly.
Replace the Transmitter
Your key fob serves as the "key" to so many of your car's most important functions, it can be a big blow in the event that you lose or damage it. A damaged or broken key fob will stop you from locking or starting your car.
It's smart to have a spare keyfob on reserve in case of emergency. Luckily, the process of replacing your Nissan key fob is relatively straightforward. You'll require a new battery and a small screwdriver for removing the old one The replacement process is very easy and should only take a few minutes.
img width="434" src="
">
You'll require a round Panasonic CR 2032 3V battery (you can usually find them in multipacks for less than $5 USD). The battery is located in the back half and you'll need gently push the two halves in order to expose it. Use https://www.thekeylab.co.uk/nissan-car-keys/ to push the clip on top of the battery and remove it, taking note of the location. Replace the battery, and then put it back together to form the key fob. Check it out to confirm it is working.
As with any electronic device, the Nissan Intelligent Key will eventually wear out due to regular usage and require to be replaced. To prevent this you should try to protect your key fob from magnetic fields, water as well as physical impacts Make sure not to drop it or put too much pressure on it.
Replacing the Key
If your Nissan key fob dies in the middle, you won't be able to use it to unlock your vehicle or to start it. This is a problem for those who must go to work in Detroit or run errands around Dearborn.
It's not that difficult to change the battery on your Nissan Smart Key. You can replace the battery at home or in the dealership. A pack usually costs less than $5.
Begin by flipping the fob over and pressing a small catch on the back. This will release the mechanical emergency key. While you won't be in a position to use the emergency key to start your vehicle but it will allow you to open the door.
Then look for a tiny slit on the top of the key fob casing. These are perfect to insert an screwdriver through the hole, allowing you to pull the two pieces of the key fob apart. Once you've got access to the internal battery, you can remove it and take note of its location. When you're ready to reassemble the key fobs, slide the new battery back into its place and snap the two parts of the case together. Then, insert the mechanical key, and your Nissan smart key will function as normal.
Other Problems
A lot of modern cars have key fobs, which let you to lock them and start them without having a physical key. To do this, the key fob uses a small transmitter to communicate with the car's computer system.
If your Nissan key fob stops working after you change the battery it could be due to various reasons. For one, the new battery might not be properly seated in the key fob. Resetting the key fob is another possibility. This is a straightforward process that you can do at home with just a few tools.
For instance, you'll require the screwdriver, which should be preferably a flat head, to open the key fob to remove the battery that was in there. With a screwdriver, pull the back of the keyfob and insert the new batteries. Finally, you'll need to change the programming of the key fob to ensure that it is compatible with your vehicle.
You can easily program your Nissan key fob by yourself, as they are all user-programmable. This is usually done by inserting your keyfob into the ignition twice in five seconds. If this fails, you can bring your key fob to a dealer or auto locksmith to get it programmed. The cost will differ based on the person you speak to and the type of vehicle you own.
![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
