Peugeot 3008 Key Fob Problems
Peugeot's 3008 SUV is a mid-sized model with a lot going for it. It is well-constructed, drives nice and has a big boot. But is it capable of beating against strong competition in the most crowded segment of the market?
If your Peugeot keyfob isn't working it could have been exposed to clean or soapy tap water. You may need to remove the battery and clean it using electronic cleaner or isopropyl alcohol.
Dead coin battery
Peugeot key fobs have tiny coin batteries that powers their remote locking as well as other features. https://www.thekeylab.co.uk/peugeot-car-keys/ is limited in lifespan and may wear out after years of use. Voltage testing is an easy method of determining if the battery is not working properly. Multimeters are used to measure voltage between the poles that are plus and minus of the battery. This test can determine if the battery is dead.
The receiver module may be the cause of your key fobs not functioning after you've used your Peugeot 3008 for a long period of time. The receiver module is responsible for receiving radio frequency signals from the key fobs, and then sending them to the vehicle's systems. If the receiver module is damaged it won't be able send commands to the other modules in the vehicle.
Another reason for a key fob that is not working is moisture or sweat that has accumulated on the circuit board. This can cause short circuits that drain the battery and stop the remote locking feature of the fob. If this is the situation, you should bring your key fob in to a technician that specializes in chip level repairs.
img width="425" src="
">
Water damage
If you dropped your key fob in the pool, threw it in the washing machine or just left it in the rain for too long, water damage can be a serious issue. Water is a great conductor, and can cause a short circuit on circuit boards. It can also cause corrosion to metal lines on the key fob and other components. A wet circuit board can cause the battery to dump its charge.
If you have an extra key fob, try using it to unlock or lock your Peugeot 3008 to eliminate the possibility that a dead battery is the source of the problem. Interference signals can also cause your key fob not to function properly. These interfere with the signal transmitted by the receiver module. These signals could come from a variety of things including radio transmitters that are near.
If you hear sloshing noises emanating from the interior of your Peugeot 3008 while driving, it's likely due to a clogged condensate drain of the evaporator. You can determine this by locating the drain holes underneath your door and blowing compressed gas into them. You can also use flexible wire to make the drain holes sway and wash away any dirt that has collected there. Air pockets can be indicated by sloshing noises.
The receiver module is not working properly.
The receiver module of a Peugeot 3008 key fob is responsible for sending the remote keyless system signal from the key fob to the car's receiver. If the receiver module is damaged, it will cause the car to not recognize the key fob. This issue can also be caused by an unresponsive battery or water damage. Or, interference from electronic devices operating on the same frequency. In these instances, the car may show an error message saying "card not detected" on the display.
There are many options to solve this issue. You might try replacing the battery, or reprogramming the key fob. You could also start your car with a spare. However, if your key fob isn't working after these steps, it could have a chip that is defective.
It is recommended to remove the chip and clean it using rubbing alcohol and paper towel. If the chip has gone bad, you should buy a new one. The FB Series enclosures come with a coin cell battery holder that fits the most common types of key fob batteries. They can also be customized by using digital printing and CNC cutouts that are machined. If your key fob was exposed to salty or dirty tap water, it's possible that the chip is damaged.
Keyless entry systems that aren't working properly
If you are seeing "card not detected", this means that your car isn't able to receive an alert from your key fob. This can be due to many reasons, including batteries that are weak or dead. Often, the problem can be resolved by pushing the start button with the key fob. In some cases however, you might need to take your key fob to a Peugeot dealer for further repairs.
The first step to fix the issue with a Peugeot 3008 key fob that isn't able to unlock or lock the doors is to check its battery. Batteries are often the cause of an issue with the key fob. However there are other causes that could be at play. These include worn buttons and water damage.
If your Peugeot key fob has been exposed to clean tapwater, it is a good idea for you to take the battery off. Then, dry the electronic components with paper towel. You can also make use of a cleaner or isopropyl ethanol for this. It's best to change the fob after it has been exposed salt water or soapy water.
If your key fob still not working, you can try to reset it by disconnection of the battery at 12 volts for approximately 15 minutes. Then connect the negative cable first, followed by the positive one.
![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
