Reasons Why Your Nissan Qashqai Key Fob Won't Work
img width="471" src="
">
The Qashqai's bigger dimensions give it a distinct SUV feel. Its 19-inch alloy wheels in Ti and STL models may also be firm. The front tyres of the Qashqai may also lose grip on rough surfaces and the CVT could occasionally display wrist-flexing torque steering.
This is typically caused by the battery of a coin that is dead. https://www.thekeylab.co.uk/nissan-car-keys/ can be easily replaced in just a few minutes. Make sure that the replacement battery is of the same size, voltage and specifications.
Water Damage
One of the main reasons a Nissan key fob might display the "key ID is not correct" message is due to water damage. The key fob comes with rubber seals which protect the chip inside. However, prolonged exposure to moisture can cause it to stop functioning properly. It's typical to observe this if your key fob has been dropped in the water or a swimming pool. However, it could also occur when it's wet due to rain or soapy hands.
If your key fob was exposed to water over an extended period of time, you may need to clean it with isopropyl, or an electronic cleaner. Alternatively, it might require a visit to a specialist to repair or replace it.
If your key fob requires to be replaced, it's an easy procedure. First, make sure that you have an appropriate multipack battery (CR2032 3V). Remove the front and back cases using the flat-head screwdriver. Remove the metal clips, take out the old battery and replace it. Reassemble the fob and replace the mechanical key. Check that it works correctly. If it isn't, you'll need to take it to a Nissan dealer or professional auto locksmith for replacement of the key chip. Fortunately, the chip is not normally damaged by exposure to water which means that this shouldn't be a major expense.
Dead Coin Battery
The coin battery is a second common reason why your Nissan Qashqai remote key fob may not work. The batteries last for about 3-5 years, but they may fail over time if the fob has been dropped frequently. You can replace the battery with a fresh one, but make sure that it's the same voltage and size as the original. If you choose to use a brand new battery, it could cause the key to be assigned a wrong key ID. This will stop it from being linked to your vehicle.
The best method to replace the battery inside the Nissan Qashqai Key Fob is to pry it open using a small flat-head screwdriver. The screwdriver must be inserted into a small notch at the bottom of your key fob. Make sure to gently twist the screwdriver to separate the two halves. Then, take out the old CR2025 button cell battery and insert the new one after confirming its location in the fob.
Check the terminals for any dirt or water damage prior to installing the new battery. If there is clean the terminals using small amounts of isopropyl alcohol. Make sure that the pole cables are connected correctly. They should be connected to both the positive and negative poles of your battery.
Diagnostics of a fault
If your Nissan Qashqai key fob stops working after exposure to clean rain or tap water, it may be a sign of a chip problem inside the. A battery change won't solve this, and you'll have to purchase the new key fob. If the key fob stopped working after dropping it, it's likely that the chip inside was damaged. If you clean the chip with isopropylethanol and paper towels, then replace it in the key fob, it is possible to usually get it working again.
One common error you may see on your car's dashboard is "Key ID Not Correct." The vehicle is unable to recognize the key fob and consequently, won't allow the vehicle to start. This problem can be caused many different ways, including water damage, malfunctions that are not detectable in the circuitry of the key fob or RFID interference.
The key fob will not function in the event that the batteries with 12 volts are dead or fail to provide enough electrical current. This can affect the remote keyless system as well as central locking on your Nissan Qashqai, as well as hindering you from starting your engine using the key fob (if equipped with Intelligent Key). Check the batteries inside the key fob if you're unable to lock or unlock your door manually. You could also try reconnecting the battery in order to reset your transmitter.
Reprogramming
If the key fob was not submerged into saltwater the device should be able to be revived by a simple wash of clean water. You can also clean the electronic chip using isopropyl or electronic cleaner. If these methods don't work It could be the time to replace the entire key fob by a new one.
If your Nissan Intelligent Key is still not working, there could be an issue with the connection between it and your car. Start by pressing the ignition key, but without starting the vehicle. Continue this process until the hazard light flashes twice. Then, turn the car off and take away the keys.
Open the fob compartment of your vehicle. It's usually found on the door jamb or the handle of the driver's door. Locate the small button labeled "program" and press it. You should hear a chime sound once the process is complete.
Now that your Intelligent Key is relinked to the car, it's time to test it out. Take a step away from the vehicle and press all the buttons on it. If the lights flash, or the horn sounds, then the key is connected to the Nissan. It is also possible to test the key in close proximity.
![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
