Peugeot 3008 Key Fob Problems
Peugeot's mid-sized 3008 SUV has a lot going for it. It's smooth to drive, looks great and has a big boot. Can it compete in the most competitive segment of the market perhaps?
If your Peugeot keyfob doesn't work it is possible that it was exposed to soapy or clean tap water. You may need to remove the battery and clean it with electronic cleaner or isopropyl alcohol.
Dead coin battery
Peugeot key fobs are powered by the coin-sized battery. The power utilized to operate the remote locking system, as well as other functions. The battery has a short time of life and will wear out after years of use. A simple way to check whether the battery is faulty is by performing an examination of voltage. A multimeter is used to determine the voltage between the battery's plus and negative poles. The results of this test will tell you whether the battery is dead or not.
If you've been using your Peugeot 3008 for a while, and your key fobs have stopped functioning, it could be a problem with the receiver module. The receiver module is responsible for receiving radio frequency signals generated by the key fobs and then sending them to the car's systems. If the receiver module malfunctions, it will not be able to send commands to other modules inside the vehicle.
Moisture or sweat that gets on the circuit board is a common cause of an unworking key fob. It can trigger short circuits that drain the battery and disable the feature that locks the fob's remote. If this is the situation you should take your key fob to a technician who specializes in chip level repairs.
Water damage
Water damage can be a concern in the event that you dropped your keyfob by the swimming spa, washed it or left it out in the rain. https://www.thekeylab.co.uk/peugeot-car-keys/ is a fantastic conductor and can easily damage the components of the circuit board. It can also cause corrosion to metal traces on the key fob as well as other components. A wet circuit can also cause the battery to lose its charge.
If you have an extra key fob use it to lock or unlock your Peugeot 3008 to rule out the possibility that a dead coin battery is the cause of the problem. Another issue that may prevent your key fob from functioning correctly is interference signals that interfere with the signal transmitted to the receiver module. These interference signals are triggered by a variety of sources that include radio transmitters within the area.
If you hear sloshing noises coming from your Peugeot 3008 when driving it could be due to a blocked condensate drain for the evaporator. You can check for this by looking for the drain holes beneath your door and blowing compressed air through them. You can also use flexible metal wire for wriggling drain holes to clean any dirt that has been accumulating. Air pockets can also be identified by sloshing sounds.
A malfunctioning receiver module
The receiver module of the receiver module of a Peugeot 3008 is responsible for transmitting the remote keyless signal from the keyfob to a receiver inside the car. This module can be damaged, preventing the car from acknowledging your key fob. This issue can also be caused by an inactive battery or water damage. Or, interference from electronic devices operating at the same frequency. In these cases the message "card not detected" could appear on the display.
There are many ways to fix this problem. Try replacing the battery or reprogram the key fob. You could also start your car using a spare key. If the key fob doesn't work after following all these steps, it may be due to a defective chip.
img width="387" src="
">
The best way to know if the key fob has an issue with its chip is to remove it and clean it with paper towel and rubbing alcohol. If the chip is damaged it is recommended to buy an entirely new one. FB Series enclosures are designed for a key fob and include an optional coin battery holder that can fit the most common types of key fob batteries. They can also be customized with digital printing and CNC cutouts that are machined. If your key fob has been exposed to dirty or salty tap water, your chip may be contaminated and must be cleaned.
Keyless entry systems with malfunctions
If you see the message "card not detected" It means that your vehicle is unable to receive the signal from your key fob. This could be caused by many different reasons like a dead or weak battery. The problem can often be solved by pressing the start button on the key fob. In some instances, however, you may have to take the key fob to a Peugeot dealer for further repairs.
The first step in identifying the cause of the issue with a Peugeot 3008 key fob that isn't able to unlock or lock the doors is to test its battery. Batteries are often the cause of a malfunctioning key fob. However, there are also other factors that may be involved. They include worn buttons, water damage, receiver module issues and signal interference.
If you've recently had your Peugeot key fob exposed to clean tap water it's best to remove the battery and dry the electronic components using paper towel. You can also use isopropyl alcohol or a cleaner for this purpose. It is recommended to replace the fob when it has been exposed to salt water or soapy water.
If your key fob still not working, you can try to reset it by disconnection of the battery with 12 volts for about 15 minutes. Then, reconnect the negative cable first, then followed by the positive cable.
![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
