Reasons Why Your Nissan Qashqai Key Fob Won't Work
The Qashqai's large dimensions give it a distinct SUV feel. Its ride on 19-inch alloy wheels in Ti and STL versions can also be firm. The front tyres may lose grip on rough surfaces and its CVT could occasionally exhibit wrist-flexing torque steer.
This is usually caused by dead batteries, which can be replaced in just a few minutes. Make sure that the new battery is the same voltage, size, and specification.
Water Damage
img width="475" src="
">
One of the most common reasons that a Nissan key fob gives the "key ID is incorrect" message is due to water damage. The rubber seals on the key fob protect the chip's electronic circuit, but long-term exposure to moisture can cause it to stop working properly. This is often the case when you drop your key fob into the ocean or into a swimming pools, but it could happen when it's wet from rain or soapy hands.
If your key fob was exposed to water over many years, you may need to clean it using isopropyl or electronic cleaner. It may also require a visit to an expert to repair or replace it.
If your key fob does need to be replaced, the procedure is relatively simple. First, ensure that you have a multipack of the right battery (CR2032 3V). Then, open the front and back cases with the help of a small screwdriver. Remove the clips made of metal, then remove the battery, and then replace it. Reassemble the fob and replace the mechanical key. Check to see if it functions correctly. If not then you'll need to take it to a local Nissan dealer or an expert locksmith to replace the chip on the key. Fortunately, the chip is not often damaged by water exposure which means that this shouldn't be a major expense.
Dead Coin Battery
The coin battery is another common reason for why your Nissan Qashqai remote key fob won't work. These batteries last for three to five years, but may fail over time in the event that the fob has been dropped often. You can replace the battery but be sure to use the same voltage and the same dimensions as the original. If you install a new battery, it may cause the key to be assigned an incorrect key ID. This will prevent it from being paired with your vehicle.
The best method to replace the battery of a coin on a Nissan Qashqai key fob is by removing the fob with an incredibly small screwdriver with a flat head. The screwdriver should be inserted into a small notch at the bottom of the fob, and twist it gently to split the two parts of the key fob. Remove the old CR2025 battery and replace it with a brand new one, taking note of the location of the old one within the fob.
Before putting the new battery into place, make sure there is no dirt or water damage to the terminals. If https://www.thekeylab.co.uk/nissan-car-keys/ is the case clean the terminals using small amounts of isopropyl alcohol. Make sure that the pole cables are properly connected. They must be connected to the negative and the positive poles of your battery.
Troubleshooting
If your Nissan Qashqai key fob stops working after exposure to clean tap water or rain it could be a sign of an internal chip problem. You'll require a new fob if you are unable to fix the issue by replacing the battery. If the key fob stopped working after dropping it, it's likely that the chip inside was damaged. If you clean the chip using isopropyl ethanol and a paper towel and then replace it with the key fob, you can usually get it working again.
Key ID Incorrect is a typical mistake that you might see on the dashboard of your vehicle. The vehicle is unable recognize the key fob, and thus won't allow the car to start. The issue could be caused by several things including water damage, undetectable problems in the key fob's circuitry, or RFID interference.
The key fob will stop working when the 12 volt batteries are dead or fail to provide sufficient electric current. This will affect the remote keyless system as well as central locking on your Nissan Qashqai, as well as preventing you from starting the engine using the key fob (if equipped with Intelligent Key). Examine the batteries on the key fob in case you are not able to lock and unlock your door by hand. You can also try reinstalling the battery to reset your transmitter.
Reprogramming
Unless the key fob has been submerged in salt water and is unable to be revived after a simple rinse with clean water. You may also try cleaning the electronic chip with isopropyl alcohol or an electronic cleaner. If none of the above works it is possible to replace the key fob.
If your Nissan Intelligent Key still does not work, it could be a connection issue between it and your vehicle. Start by turning the ignition key without beginning the car. Continue doing this until you see the hazards lights flash twice. Then, turn off your vehicle and remove the key.
Open the fob compartment in your vehicle's fob compartment. It is typically located in a door jamb, on the driver's side door handle or under an armrest. Locate the small button labeled "program" and press it. Once the process is completed you will hear a chime.
Now that your Intelligent Key is relinked to the car now is the time to try it out. Make sure you press all the buttons on the key while at a distance from the vehicle. If the lights flash, or the horn sounds, then the key is connected to the Nissan. You can also test it near the Nissan.
![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
