Replace Nissan Key Fob Batteries
If your Nissan keyfob does not respond to your commands, then its battery may be dead. This is a simple repair that a majority of people can handle themselves.
You can find an upgrade from a hardware store or from your owner's manual for the particular model you have, and you'll need to follow these instructions to change the battery.
Change the Battery
img width="458" src="
">
The key fob of your Nissan model is equipped with an internal lithium battery which will eventually lose charge. The battery for the key fob can be replaced in just a few minutes. You'll first need to purchase a CR2032 battery. It's a tiny coin-cell battery that is used in most key fobs. You can purchase it in most convenience stores. You'll also require a pair of gloves (latex or non-latex) and a small screwdriver with a flat head to open the fob. Before you begin, make sure to consult the owner's manual to find specific steps and directions.
After you have the new battery, remove the old one by turning the fob upside down and looking at the backside. There is a tiny catch that you must release by pulling it down. This will take the mechanical key from the original position within the fob.
Next, insert the new battery and ensure it is oriented correctly. Once the battery is inserted, close the fob and press the two sides together. After completing this last step verify your key fob by pressing the unlock button, and then seeing what happens. It's now possible to use the numerous features of your Nissan when everything is functioning correctly. It's recommended to re-program your key fob after replacing the battery to ensure it's functioning properly.
Replace the Transmitter
Your key fob is the "key" for many of your vehicle's most essential functions. It could be a major loss should it become lost or damaged. A damaged or dead key fob could prevent you from locking or starting your car.
It's a good idea to keep an extra key fob on hand in case of an emergency. The process of replacing your Nissan keyfob is fairly simple. You'll require a new battery and a small screwdriver for removing the old one The replacement process is a breeze and should only take about a couple of minutes.
You'll need a round Panasonic CR 2032 3V battery (you can usually find them in multipacks for less than $5 USD). The battery is located inside the key fob's back half and you'll need to gently push the two halves in order to expose it. Make use of a flathead screwdriver or smaller flatheads to unbolt the clip that is on top of the battery. Make sure to note the location. Replace the battery and then assemble the key fob. Test it to make sure it is working.
Nissan Intelligent Keys will eventually get worn out and require to be replaced, just like any other electronic device. Protect your key fob against magnetic fields, water and physical impacts. Be careful not to drop it or apply too much pressure to the device.
Replacing the Key
If your Nissan key fob is no longer working and you're unable to use it to unlock or start your vehicle. This is a problem for those who need to get to work in Detroit or run errands in Dearborn, or go out for an evening out near Troy.
The good news is that the battery in your Nissan smart key isn't a problem to replace. https://www.thekeylab.co.uk/nissan-car-keys/ can do it at home or at the dealership, and you can usually locate a pack for $5 or less at a hardware store.
Begin by flipping the fob on its side and pushing a small latch on the back. This will trigger the mechanical emergency key. The emergency key will not allow you to start your vehicle, but it will open the door.
Look for a small opening at the top of the casing. You can make use of a screwdriver to pull away the two parts of the key fob. Once you've accessed the internal battery, remove it and note its position. When you are ready to put back together your key fobs, insert the new battery and snap the two pieces of the case back together. Then you can insert the mechanical key and your Nissan smart key will operate as usual.
Other Problems
Many modern vehicles are equipped with key fobs that permit the user to lock and start them without having an actual car key. To accomplish this the key fob makes use of an electronic transmitter to connect with the car's computer system.
There are a variety of reasons that your Nissan key fob does not work after replacing the battery. One possibility is that the new battery wasn't properly fitted into the key fob. Resetting the key fob is also a possibility. It's an easy task that can be completed at home with the help of the right tools.
For example, you'll need a screwdriver, preferably a flat head to remove the key fob, and then remove the battery that was in there. Then, using a screwdriver, pry the back of the keyfob open and insert the new batteries. You'll also need to reset your key fob to allow it to function with your vehicle.
You can easily program your Nissan key fob yourself as they are all user-programmable. It is typically done by inserting the keyfob into the ignition two times in five seconds. If this does not work, take your key fob in to an auto locksmith to have it programmed. The cost for this will depend on the person you talk to and the kind of vehicle you own.
![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
