How to Fix Common Mazda 3 Key Problems
The Mazda 3 is an elegant compact car with a premium interior and a nimble handling. It is also a great deal cheaper than many other compacts on the market.
Lost keys can be a real problem. It can be costly to replace spare keys and towing your car to a dealer to reprogram your key.
Keys not locking or unlocking doors
Leaving the doors unlocked could be very dangerous, especially when the vehicle is moving. If the door is opened when the vehicle is moving it could cause passengers to fall out or suffer injuries. To avoid this risk, you should always keep the keys away from children. Children might find them interesting and play around with them. This could cause the power window or other controls to be activated and even move the vehicle.
If you notice that the key fob isn't locking or unlocking the doors, it could mean that the battery is dead. The button cell battery on the key fob has a short lifespan, therefore it is essential to replace it frequently. A good battery will last between two and four years. It is important to replace the battery with a battery that is of the same voltage and same size as the original.
A key pairing issue could also be the reason behind your key fob not working. It is possible that the keyfob wasn't properly connected to the vehicle at the time it was purchased. In this scenario, it will need to be reprogrammed by the dealership. Fortunately it is possible to do this in less than a minute. The dealer can also reset the onboard computer to erase any remaining electric current. This will not fix the problem with your key fob's ability to lock or unlock doors.
Dead coin battery
It's possible that the battery is dead if the key fob isn't turning on or unlock your car. This is a typical issue however it can be easily solved. You can replace the battery on your own, saving a trip to the dealership. The process is easy and requires only two tools.
Press the auxiliary key button on the back of the Mazda flip key. This will open the metal auxiliary key, allowing you to take it off. There's an opening on each side of the case once the auxiliary's metal is removed. Make use of a tape-wrapped flathead screwdriver to break open the case beginning with one side, and then the opposite. Gently pry apart the two halves, then set them aside.
Now you'll be able see clearly of the key fob's battery, so you can replace it. It is important not to damage the rubber ring on which the battery is mounted. After the battery has been replaced, you can put it back into the case and enjoy your new key fob!
img width="479" src="
">
The majority of stores that sell batteries have a replacement battery. Look up a CR2025 battery. These batteries are commonly used in watches and calculators but can also be found in auto parts stores and on the internet. It's easy and quick to replace the battery in your Mazda 3. This will save you money by avoiding an appointment with a dealer.
Key pairing issue
If you've been driving your Mazda 3 for a long time, but it suddenly stopped working, there might be a problem with the remote keyless system receiver module. This is more likely to occur when the chip inside the key fob is damaged. This can be caused by many factors such as a dropped or wet key.
Fortunately the key fob's electronic chips are protected by rubber seals and should be fine even with a splash of water. However, submerging it into the pool or ocean water is an issue that is much more severe due to the highly electrically conductivity of salt could cause damage to the electronics.
If your key fob is not working, you're likely in need of a new battery. A quick search on internet will show that there are numerous third-party replacement batteries. It's important to keep in mind that these batteries might not work with your Mazda 3. It's best to purchase one from a dealer and make sure it's sure to work with your vehicle.
After replacing the battery, you'll be able use your key fob again. However, if the remote doesn't respond when you press the lock button, the key is likely stuck in power-saving mode. To get it out of this mode you'll have to press the lock button five times, and hold it until the red light turns on.
Reprogramming the key
Mazda's keyless entry system lets you to unlock the car and then start it without the requirement for an ordinary key. This is a fantastic convenience however, the process of reprogramming your remote or the key could be difficult for some. It also requires a machine that only the dealer or automotive locksmith can access. This machine is connected with the computer in the vehicle and then begins the process of programming for the new key or remote.
The first step is having at minimum two keys that are compatible for the Mazda. Then you can begin the reprogramming of an existing key. Initially the functions of the new FOB are turned off to safeguard the vehicle from theft. Once you've resettled the new key, you can enable these functions once more.
After that, you will be able to use the new key to open the doors and then start the engine. Check it out first to make sure it is working. Keep a spare set of keys around if you are worried about losing your keys.
It is easy to add the spare Mazda key. You can save money by following these easy steps. https://www.thekeylab.co.uk/mazda-car-keys/ will also help you avoid the cost of towing and save money on a spare key.
![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
