Reasons Why Your Nissan Qashqai Key Fob Won't Work
img width="499" src="
">
The Qashqai has a distinct SUV-like appearance due to its larger dimensions, and the 19-inch wheels on Ti and ST-L models can be a bit stiff at times. Its front tyres can also lose grip on rough surfaces, and its CVT can occasionally display wrist-flexing torque steer.
This is typically caused by the battery being dead that can be replaced in just a few minutes. Make sure the new battery is of the same voltage, size and specification.
Water Damage
One of the most common reasons that a Nissan key fob displays the "key ID incorrect" message is due to water damage. The key fob has rubber seals that protect the chip inside, but prolonged exposure to moisture can cause it to cease functioning properly. This is typically the situation when you've dropped your key fob into the ocean or into a swimming in a pool, but it can occur if it becomes wet due to rain or soapy hands.
If your key fob has been exposed to water for many years, you may need to clean it with isopropyl, or an electronic cleaner. It could also have to be taken to a specialist to be repaired or replaced.
If your key fob does require replacement the process is simple. Make sure you have the proper multipack (CR2032, 3V). Remove the front and back cases with a flathead screwdriver. You'll need to take out the metal retaining clips and push out the old battery and replace it with the new one. Reassemble the fob and replace the mechanical key. Check to see if it functions correctly. If not then you'll have to go to your local Nissan dealer or a professional auto locksmith to replace the chip on the key. Fortunately the chip isn't normally damaged by exposure to water and this shouldn't be a major expense.
Dead Coin Battery
The coin battery is another common reason for why your Nissan Qashqai remote key fob might not function. The batteries typically last between 3-5 years, but they may fail over time, particularly when the fob is dropped frequently. You can replace the battery, however, make sure it's the same voltage and the same dimensions as the original. If you are using a different battery, it can cause the key to have an incorrect key ID, which can prevent it from pairing with your vehicle.
The most efficient method to change the coin battery in the Nissan Qashqai Key Fob is to break it open using an small screwdriver that has a flat head. Insert the screwdriver into a small notch at the bottom of the fob and twist it gently to split the two parts of the key fob. Remove the old CR2025 battery and replace it with a new one, making note of the position of the old battery in the fob.
Before you put the new battery in place be sure that there is no dirt or water damage on the terminals. If there is clean the terminals using a small amount isopropyl ethanol. Make sure that the pole cables are connected correctly. They should be connected to the negative and the positive poles of your battery.
Diagnostics of a fault
If your Nissan Qashqai key fob stops working after exposure to clean tap water or rain, it may be an indication of a chip problem inside the. You'll need a new keyfob in the event that you can't resolve the issue by replacing the battery. If the key fob didn't work after you dropped it, it's likely that the chip inside was damaged. It is possible to get the key fob back to work once again if it is removed and clean the chip using alcohol and paper towels and then insert it back into.
https://www.thekeylab.co.uk/nissan-car-keys/ might see on your dashboard is "Key ID Incorrect." The car is unable to recognize the key fob and thus won't allow the car to start. The issue could be caused by a variety of factors, including water damage, undetectable faults in the key fob's circuitry or RFID interference.
The key fob will not function if the 12 volt batteries are dead or fail to provide enough electric current. This could affect the remote keyless system and central locking on your Nissan Qashqai, as well as stopping you from starting your engine using the key fob (if equipped with Intelligent Key). Check the batteries in the key fob if it is unable to lock or unlock your door by hand. You can also try re-inserting the battery to reset the transmitter.
Reprogramming
If the key fob was not submerged into saltwater, it should be able return to life with a simple wash of clean water. You might also try cleaning your electronic chip with isopropyl alcohol or an electronic cleaner. If these methods don't work, it may be time to replace the entire key fob with a new one.
If your Nissan Intelligent Key is still not working, there could be an issue with the connection between it and the car. To reconnect it, begin by turning the key in the ignition but without starting the car. Continue this process until the hazard lights flash twice. Then, turn the vehicle off and take away the keys.
Then, you need to open the fob compartment in your vehicle. This is usually located in a door jamb on the handle on the driver's side or under the armrest. Find the small "program" button and press it. You will hear a sound after the process is completed.
It's time to test your Intelligent Key to the test. Press all the buttons on the key while at a distance from the vehicle. If the lights flash, or the horn sounds, then the key is connected to the Nissan. You can also test it near the Nissan.
![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
