Peugeot 3008 Key Fob Problems
Peugeot's mid-sized 3008 SUV has a lot of positives. It is well-constructed, drives great and has a big boot. Can it compete in the most competitive segment of the market perhaps?
If your Peugeot key fob isn't working, it could have been exposed to clean tap water or soapy water. You may need to take off the battery and clean it with isopropyl ethanol or electronic cleaner.
Dead coin battery
Peugeot key fobs are powered by the coin-sized battery. The power utilized to operate the remote locking mechanism and other features. This battery has a finite life span and may get worn out after years of use. Voltage testing is an easy method of determining if the battery is defective. Multimeters are used to measure the voltage between the poles that are plus and minus of the battery. The results of this test will show whether the battery is dead or not.
The receiver module may be the reason behind the key fobs that you have not been able to use after using your Peugeot 3008 for a long time. The receiver module is responsible for receiving radio frequency signals received by key fobs and then sending them to car systems. If the receiver module is defective it won't be able to transmit commands to the other modules within the vehicle.
Another common reason for the key fob not working is moisture or sweat in the circuit board. This can lead to short circuits which drain the battery and disable the remote locking feature of the key fob. If this is the case you need to bring your key fob to a technician that specializes in chip level repairs.
Water damage
Water damage can be a problem in the event that you dropped your keyfob in the swimming pool, washed it or left it in the rain. Water is a fantastic conductor and can easily cut off parts of the circuit board. It can also cause corrosion to the metal traces on the key fob as well as other components. A wet circuit could cause the battery to lose its charge.
If you have an extra key fob, use it to lock/unlock the Peugeot 3008 in order to eliminate a dead coin-cell battery as the cause of the issue. Interference signals can cause your key fob to stop working properly. These interfere with the signal transmitted by the receiver module. These signals can come from a variety of sources such as radio transmitters in close proximity.
If you hear sloshing sounds coming from your Peugeot 3008 when you drive it could be caused by a blocked condensate drain from the evaporator. You can test this by blowing compressed air through the drain holes under your door. You can also use a flexible metal wire for wriggling drain holes to clean any dirt that has been accumulating. The sound of sloshing can also indicate that there are air pockets within the cooling system.
A malfunctioning receiver module
The receiver module in the receiver module of a Peugeot 3008 is responsible for transmitting a remote keyless message from the keyfob to a receiver inside the car. This module can be damaged and block the car from being able to recognize your key fob. This issue could be caused by the battery being dead or water damage. Also, interference from electronic devices operating on the same frequency. In these cases, a message stating "card not detected" may appear on the display.
Luckily, there are a number of ways to resolve this issue. You can try replacing the battery or reprogram the key fob. You may also be able to start the car with a spare. If the key fob still isn't working after all these steps, then it may be due to a defective chip.
It is best to get rid of the chip and clean it with rubbing alcohol and paper towel. If the chip is fried you should purchase a new one. FB Series enclosures are designed for a key fob and come with a coin battery holder that can fit the most common types of key fob batteries. The enclosures can be personalized with digital printing and CNC-machined cutouts. If your key fob was exposed to salted or dirty tap water, it's possible that the chip has been contaminated.
Keyless entry systems that fail
If you get "card not detected" This means that your car isn't able to receive an alert from your key fob. This can be due to many reasons like a dead or weak battery. Most of the time, the issue can be solved by pressing the start button with the key fob. In certain cases, you might require taking the keyfob to an Peugeot dealer for repairs.
The first step to troubleshooting a Peugeot 3008 key fob that's not able to unlock or lock the doors is to test the battery. Batteries are often the root of a malfunctioning key fob. However there are other reasons that could be involved. This includes worn buttons, damage to the receiver module, water problems and signal interference.
If your Peugeot key fob has been exposed to pure tap water, it's recommended to remove the battery. Then, dry the electronic components using paper towel. https://www.thekeylab.co.uk/peugeot-car-keys/ could also try using isopropyl ethanol or a cleaner for this purpose. It's best to change the fob if it has been exposed to salt or soapy water.
img width="331" src="
">
If your key fob is not working, try to reset it by disconnection of the 12 volt battery for about 15 minutes. Then reconnect the negative cable first, then followed by the positive one.
![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
