Changing the Battery in Your Mazda 3 Key Fob
It can be a bit frustrating to pull into your car at the conclusion of a long and tiring day and discover that your key fob is dead. Luckily, it's an easy fix by purchasing simple battery replacement from a hardware store or big box retailer.
Incorporating a spare key fob to your Mazda 3 can be an inexpensive way to save yourself from having to be transported to a dealership and having them re-program your keys.
Battery Replacement
You can replace the battery on your Mazda 3 keyfob at home. But, it is best to replace the battery if it fails, or when the key fob shows a message on the multi-information display, "Low key fob battery. Replace battery."
To open the key fob's casing you'll need a tape-wrapped flathead screwdriver and a bit of patience. Find a gap or notch in the bottom portion of the metal of your Mazda 3's key fob and then insert the head of the screwdriver in it to pry off the lower part. Repeat this process for the top metal piece but be careful not to scratch the rubber ring that is at the bottom of the key fob's case.
You'll find a slot on each side of the case that contains the battery. Start with one side of the case, and then gently lift it up. Remove the old CR2025 and replace it with a new one, making sure you put it on its face to ensure the correct polarity. Finally, put the cap of the battery back on and reattach both sides of the key fob's case, pressing until you can hear them click.
After replacing the battery Lock and unlock your doors to verify whether the fob is working. If everything appears to be working then you can begin using your Mazda 3's remote features on the road again!
Pairing Issues
If your key fob stopped functioning suddenly it could be because the transmitter inside the car has been damaged. This is usually a matter to a professional and you require a new key fob.
If you've tried replacing the battery and programming the key fob, but it did not resolve the issue it could be that the chip in the key fob might be damaged. This could be the case if the keyfob was dropped, exposed to saltwater, or touched by dirty fingers.
You will need to locate a small "key" that is built into the seam to remove the circuit board to identify the issue. Then, you will be able check for any corrosion or damage on the chip. To avoid damaging the microchip, it is recommended to use a clean paper towel.
img width="391" src="
">
It is also possible to take a closer look at the battery connector terminals to examine if they're cracked or broken. If this is the case, carefully connecting them back can usually restore the function of the key fob. You can also inspect the buttons for damage or wear. If the buttons are loose, they can be soldered back in place and also if a button has physically snapped off.
Interference Signals
There's nothing more frustrating than trying to get the engine started in your car only to see the message "No Fob Detected". https://www.thekeylab.co.uk/mazda-car-keys/ happens at the worst time, for instance when you're late to work or have to pick up your children from daycare or school. There are some things you could do to help figure out what's causing the issue.
Interference signals can cause the remote key fob to stop functioning in a proper manner. This could be caused by objects such as buildings, weather conditions, and transmitters that use the same frequency. Interference can also occur when you have an aftermarket device installed in the vehicle that transmits on the same frequency as the key fob.
In addition, if the key fob is exposed to water or salt water it may be damaged. The rubber seals on the chip's electronic components can be damaged by water, particularly when it is submerged for an extended period of time such as in a pool or ocean at the beach. The chip can stop working and may require replacement of the keyfob. If you have a key that has the ability to be programmed, you can clean it using electronic cleaners or isopropyl to bring it back to its original function. If this doesn't help then it's likely that the chip has been damaged and must be replaced.
Locking and Unlocking the Doors
The key fob's buttons send electronic signals to a solenoid in the car that then converts that signal into a mechanical action that locks and unlocks doors. If the door lock isn't working, the issue may be a solenoid issue that requires analysis with the help of a professional auto repair shop.
A dead 12 volt battery could also prevent the fob from functioning correctly. This can happen if the battery loses its charge or if the contactors get corroded and stop transferring electricity. The good news is that a new battery is able to fix this issue in just minutes.
The receiver module could be the problem if the key fob isn't working after you replace batteries or reprogram the device. The device receives radio frequency signals from the key fob and interprets them to control the functions of the vehicle. It can be a costly repair if it becomes faulty.
To determine if this is the case, start by inserting the spare key into the key slot and turning the ignition to ON. Press the key fob twice within 10 seconds, without removing it. The Mazda 3 system will now connect the key to the car and allow you to use it as your primary remote for driving. You can program up to three keys this manner.
![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
