Reasons Why Your Nissan Qashqai Key Fob Won't Work
The Qashqai has a distinctly SUV-like feel due to its bigger dimensions, and the wheel sizes of 19 inches in Ti and ST-L models may be a bit stiff at times. The front tyres could lose grip on rough surfaces, and its CVT could occasionally exhibit wrist-flexing torque steer.
This is usually due to an unresponsive coin battery that can be easily replaced in just a few minutes. Make sure the battery you replace is of the same voltage, size and specifications.
Water Damage
Water damage is one of the most common causes for the Nissan keyfob to display the "key ID incorrect" message. The rubber seals on the key fob are designed to protect the electronic chip, but prolonged exposure to moisture can cause it not to work correctly. This is usually the case when you drop your key fob into the ocean or a swimming water pool, but it could occur if it becomes wet from soapy hands or rain.
If your key fob was exposed to water for many years, you may need to clean it with isopropyl, or an electronic cleaner. It could also have to be taken to a professional for repair or replacement.
If your key fob need to be replaced, the procedure is relatively simple. First, make sure you have a multipack with the correct battery (CR2032 3V). The front and rear cases with the flat-head screwdriver. You'll need to take out the clips for retaining metal and push out the old battery and insert the new one. Reassemble the fob and replace the mechanical key. Verify that it is working correctly. If not it is necessary to take it to your local Nissan dealer or an expert locksmith to replace the key chip. Fortunately, the chip is not often damaged by water exposure and therefore this shouldn't be a huge expense.
Dead Coin Battery
The coin battery is another frequent reason why your Nissan Qashqai remote key fob might not work. These batteries last three to five years, however they are prone to failure over time if the fob has been frequentedly dropped. You could replace the battery but make sure it is the same voltage and same dimensions as the original. If you choose to use another battery, it may cause the key to have an invalid key ID which can prevent it from paired with your vehicle.
The best way to change the battery inside a Nissan Qashqai Key Fob is to pry it open with the help of a small screwdriver with a flat head. Insert the screwdriver into tiny notch at the bottom of the fob and move it around to separate the two halves of the key fob. Then, remove the old CR2025 button cell battery and insert the new one after confirming its location in the fob.
Check the terminals for dirt or water damage prior to installing the new battery. If so clean the terminals using a small amount isopropyl ethanol. Make sure that the pole cables are properly connected. They must be connected to the negative and the positive poles of your battery.
Troubleshooting
If your Nissan Qashqai's key fob doesn't function after being exposed to pure rainwater or clean tap water it could indicate that there's a problem with the internal chip. Changing the battery won't fix this issue, and you'll have to buy an entirely new key fob. If the key fob has stopped working after you dropped it, it is likely that the chip inside was damaged. If you clean the chip using isopropyl ethanol and a paper towel and then put it back in the key fob, you can generally get it working.
img width="471" src="
">
Key ID Incorrect is a typical error that you can see on the dashboard of your car. https://www.thekeylab.co.uk/nissan-car-keys/ means that the vehicle is unable to recognize the key fob, and will not allow it to start the engine. The issue could be caused by a variety of factors including water damage, undetectable issues in the circuitry of the key fob or RFID interference.
The key fob will cease to function in the event that the 12 volt batteries are dead or don't provide sufficient electric current. This could affect the Nissan Qashqai's remote keyless system, central locking and the capability to start the engine with the key fob. If you can't lock or unlock the door by hand You should examine the batteries on your key fob and make sure they're in good shape. You can also try re-inserting the battery to reset the transmitter.
Reprogramming
If the key fob was not submerged in saltwater the device should be able to come back to life with a simple rinse of clean water. You may also try cleaning the electronic chip using isopropyl alcohol or an electronic cleaner. If none of these works then you might need to replace the key fob.
If your Nissan Intelligent Key is still not working, there could be a problem with the connection between it and your car. Start by pressing the ignition key, but without starting the vehicle. Continue to do this until the hazard light flashes two times. Turn off the vehicle and remove the key.
Open the fob compartment in your vehicle. It's usually located on a door jamb or the handle of the door for the driver. Find the small button labeled "program" and press it. You will hear a chime after the process is completed.
It's time to test your Intelligent Key to the test. Make sure you press all the buttons on the key while standing a distance from the car. If the lights flash and the horn squeaks, it means that the key has been successfully linked to the Nissan. It is also possible to test it in close proximity.
![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
