uPVC Window Repair
Despite being resistant to harsh weather conditions, uPVC can experience issues that require repair. These problems can be fixed at a fraction of the cost of replacing the window.
A common issue is that a window becomes difficult to open because its hinges are stiff. Fortunately, this problem can be easily solved by lubricating the hinges using something similar to WD-40.
Broken or cracked glass
Glass is everywhere in our homes: in doors, windows, surfaces and tables, the front of stoves and microwaves, and even in picture frames. A well-hit baseball game or rough-housing with friends could cause cracks to your windows that need to be repaired promptly before they get any worse. Fortunately, these kinds of cracks are very easy to repair without the need to replace your window's glass or frame.
To begin, clean the area with a damp cloth to remove any dirt, dust or fingerprints. Use a small amount of epoxy to seal around the crack. Allow the epoxy to completely dry before moving the window. This repair is very simple and will save you money on replacing your uPVC window.
Another common issue with uPVC windows is that the gasket of the window becomes soft or separating from the frame. This will result in a loss of insulation and allow in of water or cold air into your home. This can be easily fixed with an abrasive blade like a bank card to separate the gasket from the frame of the window. If you have a bit of time on your hands you could apply a bit more epoxy to the crack to make it look like the crack never existed in the first place.
Apply a piece of tape to fix the crack if it is too deep for you to reach it with your fingers. This will stop further damage. Alternately, you can use clear nail polish to fill in the crack and prevent it from growing further. The key is to apply this treatment immediately after you detect the crack, or it will quickly spread and be more difficult to fix.
If you want a more permanent solution consider using uPVC epoxy to repair your cracked or broken glass. It's the longest-lasting solution, but will provide the most effective results in terms of strength and appearance. Follow the manufacturer's instructions for the application of the epoxy and make sure to clean the surface with a rag dampened with acetone when it has fully dried.
Water Leaks
Upvc windows are very durable but they do require some maintenance and attention. If they're not maintained correctly, a number of problems can arise. These issues can range from leaking water around frames, or condensation inside the glass units.
A uPVC window specialist can help pinpoint the issue and fix it. They can also provide suggestions on how to prevent it happening again in the future.
Leaking uPVC Windows can be a major problem and should be addressed as soon as they begin to occur. If the issue isn't treated, it could result in major damp issues within your home. This will result in expensive repairs and an increase in energy efficiency.
In a majority of cases, a leaky uPVC window can be repaired by applying a leak patch. This sealant is applied inside the window to prevent water from entering the house through the damaged area.
Double-glazed units that are cloudy or misty could be a sign of a leaky seal. This could be due to various causes, including age, weather conditions or just wear and tear.
One way to avoid this is by having your windows cleaned on a regular basis. It is recommended that you clean your windows at a minimum of twice a yearly with an uncolored soft cloth that is soaked in warm soapy water. It's important to avoid using any colored cloths since they can leave dye stains on the plastic. For stubborn stains it is recommended to apply solvent PVC cleaner. It can be purchased from any hardware store and is simple to apply. To avoid streaks, wipe the window frames away from direct sunlight in a shady area.
Incorrectly installed hinges or locks
img width="491" src="
">
Over time, a window's hinge may be damaged or bent. This can cause a gap to form in the frame which will let in draughts and reduce the efficiency of your heating. A draught can also make your home uncomfortable and cold and can increase your heating bills.
A gap in a uPVC is a problem that can be easily fixed. A uPVC window repair specialist can identify the issue and fix it. A small hole can usually be repaired with carpenter’s glue and a wooden dowel inserted into the gap. The dowel must be positioned so that it is in line with the hinge leaf, and has a smooth surface. The carpenter's glue is spread on the dowel, and then tapped into position. When it's dry, a screw can then be installed into it to secure the hinge leaf.
UPVC window hinges and locks can become stiff over time due to general wear and tear, or due to blockages caused by dirt or other debris. They should be cleaned and inspected frequently to ensure that they are working correctly. Make use of WD-40 to keep moving parts in good working order.
It is recommended to wash UPVC windows at least twice a year. The damp cloth is coated with an emulsion of mild detergent and water. The corners of the window should be cleaned more often to prevent the accumulation of dirt and rust.
It can also be difficult to open or shut the handle of uPVC windows. This could be because of the handle falling or it can be caused by problems with the locking mechanism. This is generally a quick and easy fix and can be completed by the homeowner themselves when they follow a few simple steps.
A damaged lock could be an actual security risk since it means that your home isn't secured and could potentially be vulnerable to intruders. A broken lock can make it difficult to open your uPVC window or door and could cause hassle for you. If this is the case you may require a new handle or adjust the multipoint locking system.
Stuck Handle
If your upvc handle is stuck, it can be frustrating. Particularly when you try to open your window only to find that it needs much more force or does not open at all. The reason for this is the wire inside the handle holder that has become rough. By removing the handle and having a look at the wire, you will be able to smooth out the rough spot and this will fix your issue.
Another way this can be fixed is by using the lubricant graphite or paraffin on the pole sliders, which will then allow the handle to move up and down. https://www.repairmywindowsanddoors.co.uk/bexley-windowrepair/ is also a good time to clean your handle as this will help prevent any further issues.
Superglue can be used to fix the button in the event that the issue is with the actual push button. Superglue must be completely dry prior to using it again. If the handle is completely damaged or broken it can be fixed by purchasing a new one and then screwing it into place. This is a much easier fix than replacing the whole window frame, and is something you can do yourself, particularly if you have access to the appropriate tools.
![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
